Skip to Content
Avenue Vésale 32a, 1300 WavreBy appointment · Mon to Fri 9 am to 6 pm, Sat 10 am to 5:30 pmBook onlineNLENFRWhatsApp 0474 98 67 80

Getting started in PPF installation: equipment, budget, training

The day-one equipment, the time and the price of a front end according to our invoices, and the training to learn.
12 November 2026 by

To get started in PPF installation, you need a bodywork protection film of about 200 microns (174 and 250 also available), two solutions in spray bottles, two squeegees, a knife with new blades, a heat gun, closed and well-lit premises, and at least two days of training. Then plan weeks of practice on training parts before invoicing your first front end.

We have been installing protection film in Wavre for more than 10 years and training installers since 2020. This guide replaces our first article of 2025 on the subject. It repeats what we tell trainees on the first morning, with the figures from our own invoices.

What a PPF does, and what it asks of the installer

A PPF is a clear polyurethane sheet bonded to the clear coat. Common bodywork films measure about 200 microns, or 8 mil. They take stone chips, wash rubbing and bird droppings in place of the paint. The top layer closes over micro-scratches with heat.

The installation is done wet. You spray a slip solution on the part and on the adhesive, you position the film, then you push the water out with the squeegee from the centre to the edges. A tack solution, with more alcohol or not, depending on the technique and the film, fixes the areas that must hold straight away. The edges are tucked with a heat gun or with steam. The result is decided before installation: decontamination, degreasing, cleanliness of the premises. For the advice we give customers after installation, read maintaining a PPF.

The day-one equipment

  1. The film. A roll 1.52 m wide is the common format. Choose a brand whose supplier answers the phone and delivers in Belgium within a few days. Keep the offcuts: they are used for practice.
  2. Two labelled spray bottles. Slip solution: water and a few drops of mild soap. Tack solution: water and isopropyl alcohol. The mix is adjusted to the temperature of the room and the film; your trainer gives you a starting point.
  3. Two squeegees. A soft squeegee with felt for the surfaces, a firm squeegee for the edges and the recesses.
  4. A knife with 30° blades and new blades. A blunt blade tears the film. A cutting tape avoids putting the blade on the clear coat for cuts made on the vehicle.
  5. A heat gun or a steam machine. It is used to tuck the edges and shape the film over the curves.
  6. The preparation equipment. Neutral shampoo, iron remover, clay, degreaser, clean microfibres reserved for PPF. A clear coat on a car in use also needs polishing before installation.
  7. The premises. Closed, clean, draught-free, with raking light to see water and dust under the film. Wetting the floor before installation brings the dust down.
  8. Cutting. A plotter and pattern software cut the pieces to the shape of the vehicle. We pay about 1 500 € excl. VAT per year for unlimited cutting. At the start, have your kits cut by your supplier (or by us) and keep hand cutting for simple parts.

How long an installation takes, and what it invoices

In our invoices from 2020 to 2026, a front end represents 2.9 to 3.6 paid working days and a full vehicle 7.9 to 8.9 days. The median invoiced for a front end is 1 750 € excl. VAT over 130 invoices. Our public prices start at 1 790 € incl. VAT for a front end and 4 690 € incl. VAT for a full city car, detailed on our page about paint protection film (PPF).

A beginner takes more time and wastes film. Count it in your cost price for the first months, and refuse to install at the price of an established workshop as long as you are redoing parts.

Another figure to know before prospecting: 77% of the PPF we invoiced over two years was invoiced to companies. On PPF quotes of 1 000 € excl. VAT and more, 87% of companies signed, against 17% of private individuals. Dealerships, fleets and lease cars keep an installer in business. Private individuals compare and wait.

The starting budget, item by item

Three items weigh heavily: the film, the cutting and the training. Film is counted in rolls and wasted offcuts. Cutting is counted in credits per kit or as a subscription; our unlimited subscription comes to about 1 500 € excl. VAT per year. The two-day Introduction to PPF costs 950 € excl. VAT per trainee. Small tools and solutions weigh little against these three items.

Before buying anything, sort out your legal status and VAT. The steps from the business counter to the first ten cars are in getting started in detailing in Belgium, and they apply to a PPF installer.

The mistakes of the first month

  • A poorly decontaminated surface: every grain stays visible under the film and forces you to lift the piece.
  • Too much alcohol in the tack solution: the film sticks before it is in place.
  • Too much heat: the film stretches, shrinks as it dries and releases an edge.
  • Edges laid dry and not tucked: they lift at the first wash.
  • An installation outdoors or in full sun: the solution dries before the squeegee.
  • The blade on the clear coat: a scratch in the paint of a customer who has just paid for protection.

We correct these moves from the first day of training, like the 5 first-day mistakes in detailing.

Training: two days, then practice

The Introduction to PPF lasts 2 days, or 16 hours, in groups of 2 to 4 trainees, at the Wavre workshop, for 950 € excl. VAT. You install on real parts, you learn the two solutions, the squeegee, heat and edges. A 5-day pathway adds 3 advanced days on complete parts. We have already trained for the Forem, the CPAS social welfare centres and Territoire Zéro Chômeur. The dates are published on the training page.

After the training, install every day. Start with bonnets and doors, then move on to bumpers once a flat part comes out flawless twice in a row.

In the shop

Frequently asked questions

Can you learn PPF installation on your own, with videos?

On a flat bonnet, yes. On a bumper, a mirror or a door edge, a video does not correct your hand. Two days with a trainer save rolls of film and rework at your first customers.

Do you need a cutting plotter to start?

No. Have your kits cut by your supplier or an equipped workshop. A plotter and a cutting subscription are justified when you install every week; ours comes to about 1 500 € excl. VAT per year.

How long does a front end take?

Our invoices pay 2.9 to 3.6 days for a front end and 7.9 to 8.9 days for a full car. A beginner takes longer.

Which film thickness should you choose?

About 200 microns, or 8 mil, for bodywork. It is the format of common protection films.

How much to charge for a front end in Belgium?

In our invoices, the median for a front end is 1 750 € excl. VAT. Our public prices start at 1 790 € incl. VAT for a city car. Set your price on your real working days.

See the training dates

Nathan Fougnies, founder of Ultimate Care, Wavre

Share this post